KK Enterprises logo Electricals & Industrial
Hardware Supply

Home / Products

Catalogue

Submersible control panels, MCB boxes, concealed boxes, fan boxes and terminal lugs — everything below is stocked at our Patancheru shop. Tap a category to filter, or scroll through the full list.

Submersible pump control panel with ammeter, voltmeter, start-stop buttons and MCB

FIG. 01 — SUBMERSIBLE CONTROL PANEL

Pump House Equipment

Submersible Pump
Control Panels

A single-phase control panel built around the layout pump mechanics already know: A-meter and V-meter up top, start/stop low down, and an MCB wired straight to the motor leads. Every panel is run up and its meters checked before it leaves the shop.

Metering0–30A ammeter, 0–300V voltmeter with push-to-read button
IndicatorsPower (red) and ON (green) signal lamps
ControlsStart (green) / Off (red) push buttons
ProtectionBuilt-in MCB, C-curve, rated up to 16A, 240/415V, 10kA
WiringMarked terminals — P, N mains in; R, Y, B to motor
Use case100mm-class single-phase submersible borewell pumps
  • Tested and OK-tagged on the bench before dispatch
  • Clearly labelled terminals reduce wiring mistakes on site
  • Stocked in common HP ratings — ask us for the one matching your motor
Enquire on WhatsApp Call for Price
Metal MCB distribution box, 4-way, with hinged lockable door

FIG. 02 — MCB DISTRIBUTION BOX

Distribution & Enclosures

MCB Distribution
Boxes

Powder-coated metal enclosures for housing miniature circuit breakers, in both surface-mount and flush/concealed styles. Pre-punched cable glands and a hinged, lockable door keep the installation tidy and the breakers within reach.

MountingSurface-mount (exposed) and flush/concealed (recessed) variants
Ways available2-way, 4-way, 6-way and 8-way
BodyCRCA sheet metal, powder-coated finish
DoorHinged cover with viewing window on surface variants
EntriesPre-marked knockouts for top and bottom cable entry
Use caseHome, shop and small commercial distribution boards
  • Both surface and concealed bodies kept in stock
  • Knockouts pre-marked, no need to drill on site
  • Sized to fit standard branded MCBs and RCCBs
Enquire on WhatsApp Call for Price
Galvanised metal concealed wiring box for switch and socket plates

FIG. 03 — CONCEALED BOX

Wiring Accessories · New

Concealed Boxes

A galvanised steel box that goes into the wall before plastering, giving switch and socket plates a solid, square base to screw onto. Pre-cut knockouts take conduit in from any side, and the gauge is heavy enough to hold its shape through masonry work.

MaterialGalvanised CRCA sheet steel
Modules2M, 3M and 4M sizes
KnockoutsPre-cut entries on the back and both side faces
FixingThreaded screw lugs for switch/socket plate mounting
MountingEmbedded in wall chase before plastering
Use caseIn-wall switch boards, socket points, and modular plate housings
  • Heavier gauge than the loose hardware-store boxes — holds its shape during plastering
  • Screw lugs pre-threaded, ready for any modular switch plate
  • 2M, 3M and 4M sizes kept in stock for same-day pickup
Enquire on WhatsApp Call for Price
Octagonal metal ceiling fan junction box with mounting rod

FIG. 04 — CEILING FAN JUNCTION BOX

Wiring Accessories

Fan Boxes

An octagonal junction box cast into the slab before plastering, carrying the down-rod that takes a ceiling fan's full hanging load. Knockouts on each face take the room wiring in clean, without a separate gland plate.

ShapeOctagonal, deep-drawn metal body
Mounting rodFixed centre rod sized for standard fan down-rods
KnockoutsMultiple pre-cut entries on the side faces
FixingSide lugs for embedding in slab/false-ceiling shuttering
Use caseConcealed ceiling wiring for fans and hanging fixtures
  • Rod set and centred at the factory — no on-site fabrication
  • Deep body keeps wire joints clear of the fan canopy
  • Bought by the carton for builders and electrical contractors
Enquire on WhatsApp Call for Price
Brass and tinned copper ring-tongue terminal lugs

FIG. 05 — TERMINAL TAGS & RING LUGS

Connectors & Lugs

Terminal Tags
& Lugs

Ring-tongue and offset spade lugs for terminating motor leads, panel wiring and earth conductors onto studs and busbars. Stocked in tinned copper and brass, in the wire and bolt-hole sizes contractors actually ask for.

MaterialsTinned copper and brass
StylesRing-tongue lugs, offset terminal tags, double-hole connectors
SizingStud holes from M4 up; cable range printed on each pack
TerminationCrimp or solder, depending on size
Use caseMotor leads, panel busbars, earth terminations
  • Sold loose or by the box — buy the exact count you need
  • Brass tags for tight, offset terminal connections
  • Common sizes held in stock for same-day pickup
Enquire on WhatsApp Call for Price

Don't see the size or rating you need?

We move stock often — send a photo of the old part or panel and we'll match it.

Ask on WhatsApp Visit the Shop